November 20, 2026

Travertine pavers and travertine tiles are made from the same stone, but they are not the same product. The difference lies in thickness, finish and where the material is meant to be used. Choosing the wrong format is one of the most common mistakes on both patio and interior projects. This guide explains the formats, thicknesses and finishes available, and how to decide between indoor and outdoor use before you request a quote.

Pavers versus tiles: the basic difference

Travertine tiles are usually thinner (commonly 1.2 to 2 cm) and are designed to be bonded to a rigid substrate with adhesive, most often indoors, on walls, or on covered terraces. Travertine pavers are thicker (commonly 2 to 3 cm for bedded installation, and 5 cm or more for heavier loads or loose-laid use) and are intended for patios, paths, pool surrounds and driveways. Many products sit in between, so always confirm the exact thickness with the manufacturer rather than relying on the name.

Common formats

Formats vary by manufacturer, so the sizes below are typical rather than exhaustive:

  • Standard squares and rectangles: 30x30, 40x40, 40x60, 60x60 and 30x60 cm are widely offered; larger slabs such as 60x90 cm are also found.
  • French pattern (Versailles) sets: several sizes, commonly four, packed together in a fixed ratio to produce a random-looking, traditional layout. See the silver travertine French pattern set and the antique pattern travertine set for examples.
  • Free lengths: pavers cut to a fixed width and variable length, which makes a modern linear pattern.
  • Slabs: large formats for counters, stairs and cladding; browse the travertine slabs category.

Thickness: 2, 3 or 5 cm?

2 cm

Typically used for interior floors, walls and covered areas, and for outdoor use only over a solid, stable base with full adhesive coverage.

3 cm

The common choice for outdoor paving laid on mortar or on a prepared concrete slab. It gives a comfortable margin against breakage during installation and use.

5 cm and above

Used where the surface carries heavier loads, such as driveways or vehicle access, or where pavers are laid on a sand or gravel bed. Ask your installer which thickness your base and load require.

Finishes

The finish changes both the look and the performance. For a longer comparison, read our stone finishes guide.

  • Tumbled: softened edges and a slightly weathered surface. The classic choice for outdoors.
  • Brushed: a lightly textured surface with a worn look. Good grip, popular for terraces.
  • Honed: flat and matte. Common indoors; smoother when wet.
  • Polished: shiny and formal, best kept for dry interior areas.
  • Chiselled or split edges: for rustic effects and to hide small irregularities.

Travertine can also be supplied filled (voids closed with cement or resin) or unfilled (open natural texture). Unfilled, tumbled stone is usual outdoors; filled and honed stone is usual indoors.

Cutting direction: vein cut and cross cut

Travertine can be cut along the natural bedding (vein cut), which gives long linear veining, or across it (cross cut), which gives a cloudier, more uniform pattern. Both are valid; they simply look different. The vein-cut travertine tiles show the linear effect.

Choosing a laying pattern

The pattern changes both the look and the amount of waste. A straight (stack or running bond) layout in a single format is the simplest and wastes the least stone. A French pattern or Versailles set, with several sizes combined, gives a classic, relaxed look but needs a careful layout plan and a larger allowance for cuts. Diagonal layouts add more cutting along the edges. Free-length pavers laid in staggered rows give a clean, modern line. Whatever you choose, tell the manufacturer, because sets and calibrated formats are packed differently from loose tiles.

Calibration and tolerance

Natural stone varies. Calibrated tiles are cut to a consistent thickness and size, which makes thin-set laying and tight joints easier; uncalibrated pavers can vary by a few millimetres and are usually laid in a mortar bed with wider joints. Ask the manufacturer which applies to the product you are comparing.

Edges, steps and corners

If the paving meets stairs, a pool or a raised bed, ask for matching bullnose steps, edge pieces or corner units rather than cutting field pavers on site. Supplying the same finish and colour for every part of the project gives a more consistent result.

Indoor versus outdoor use

QuestionIndoorOutdoor
Typical thickness1.2 to 2 cm2 to 3 cm, or 5 cm for heavy loads
Common finishHoned, filled, sometimes polishedTumbled or brushed, often unfilled
Slip concernWet rooms, entrancesRain, pool splash, algae
FrostNot applicableConfirm suitability with the manufacturer; allow drainage
FixingThin-set adhesive on screedMortar bed on slab, or adhesive with full coverage
MaintenanceSealing, neutral cleanersSealing, rinsing, careful de-icing

Installation notes for outdoor paving

  • Build a stable, compacted base with drainage and a gentle fall away from buildings.
  • Use a full mortar bed or full-coverage adhesive. Spot bedding leaves hollow areas that can crack.
  • Leave expansion and movement joints, especially in large sun-exposed areas.
  • Seal with a breathable, penetrating sealer after installation, and avoid acidic cleaners, which can etch travertine.

Your installer and local building rules decide the final method, so use this as a checklist for that conversation. The outdoor natural stone guide goes deeper on weather and maintenance, and the travertine versus marble article helps if you are still comparing stones.

Calculating quantities

Measure the area, then add an allowance for cutting and breakage, more for diagonal or French-pattern layouts. Our calculator helps with quantities and container loading when you plan a bulk order.

Where to find travertine pavers and tiles

Start from the travertine category and the travertine tiles listings. Product pages such as the Noce travertine pavers and the travertine floor and wall tiles show the type of information manufacturers publish. You can also browse the entire shop.

How to request a quote

OrderFromTurkey connects buyers with Turkish manufacturers. You send a quote request, and the manufacturers confirm availability, samples and terms. A good request includes:

  • Format and thickness (for example 40x60 cm, 3 cm).
  • Finish (tumbled, brushed, honed) and filled or unfilled.
  • Colour tone and cutting direction (vein cut or cross cut).
  • Edge type, if you need bullnose or special edges.
  • Indoor or outdoor use, and whether frost applies.
  • Quantity in square metres and delivery destination.

Frequently asked questions

Can I use travertine tiles outdoors?

Thin tiles can be used outdoors on a solid, stable base with full adhesive coverage, but pavers of 3 cm or more are the usual choice. Ask the manufacturer about frost suitability.

What is the best finish for a patio?

Tumbled or brushed, because they give a natural, grippy surface and hide wear well.

Are filled or unfilled pavers better?

Both are used. Unfilled is typical outdoors for drainage and grip, and filled is typical indoors for a smoother surface.

Does travertine need sealing?

Sealing is commonly recommended, both indoors and outdoors, to limit staining. Follow the sealer manufacturer's instructions.

How much extra should I order?

Plan for an allowance for cuts and breakage, usually more for patterns and diagonal layouts. Your installer can give you a figure for the layout.

Free: Turkey Sourcing & Import Guide

MOQ, Incoterms, shipping, customs & supplier checks — get the full PDF.